Oi MB controller

Fanuc Oi MB controller maintenance

FANUCFanuc controller structure:

Motherboard: display function, transmission function, etc

CPUBoard: startup function, transmission function, etc

Power board: startup function

I/OInput/output signal function

Network card: Network transmission function

Axis card: communication function

Graphics card: display function

Memory card: storage function

FANUCCommon faults of Fanuc controller:

Not starting, crashing, power failure to light up, abnormal screen display, screen flickering, etc.

Program alarm(P/Scall the police)

alarm number Alarm content

000 The parameters that need to be powered off to take effect after modification should be powered off after the parameter modification is completed.

001 THAlarm, program format error in peripheral input.

002 TVAlarm, program format error in peripheral input.

003 The input data exceeds the maximum allowed input value. Refer to the relevant content in the programming section.

004 The first character of a program segment is not an address, but a number or "-".

005 An address is not followed by a number, but by another address or program segment terminator.

006 The symbol "-" is used incorrectly ("-" appears after an address that does not allow negative values, or two consecutive "-").

007 Decimal point“. ”Incorrect usage.

009 A character appears in a position where it cannot be used.

010 Ordered something that cannot be usedGcode.

011 A cutting feed rate has not been given.

014 The synchronous feed command appeared in the program (this machine tool does not have this function).

015 Attempting to make all four axes move simultaneously.

020 In arc interpolation, the difference in distance between the starting and ending points and the center of the circle is greater than876The numerical value specified by the number parameter.

021 In arc interpolation, the motion of axes that are not within the arc interpolation plane is instructed.

029 HThe tool compensation value in the specified offset number is too large.

030 When using tool length compensation or radius compensation,HThe tool compensation value in the specified tool compensation number is too large.

033 I programmed an intersection point that cannot occur in tool radius compensation.

034 Circular interpolation appears at the beginning or end of the program segment for tool radius compensation.

037 Attempting to use in the tool radius compensation modeG17、G18perhapsG19Change the plane selection.

038 Due to the fact that in the tool radius compensation mode, the starting or ending point of the arc coincides with the center of the circle, over cutting will occur.

041 Excessive cutting will occur during tool radius compensation.

043 An invalid instruction was givenTcode.

044 Used under fixed cyclic modeG27、G28perhapsG30Instructions.

046 G30In the instructionPThe address has been assigned an invalid value (only applicable to this machine tool)2）.

051 An impossible motion occurred after the automatic corner cutting or automatic fillet program segment.

052 The program segment after the automatic corner cutting or automatic fillet program segment is notG01Instructions.

053 In the automatic corner cutting or automatic fillet program segment, the address after the symbol "," is notCperhapsR.

055 In the automatic corner cutting or automatic fillet program segment, the movement distance is less thanCperhapsRThe value.

060 The sequence number of the instruction was not found during the sequence number search.

070 The program memory is full.

071 The searched address was not found, or the specified program number was not found during the program search.

072 The number of programs in the program memory is full.

073 Attempting to use an existing program number when entering a new program.

074 The program number is not1～9999The integer between.

076 Subroutine call instructionM98There is no address in itP.

077 Subroutines nested more than three times.

078 M98perhapsM99The program number or sequence number of the instruction does not exist.

085 When inputting a program from a peripheral, the input format or baud rate is incorrect.

086 Using a tape reader/When the perforating machine interface is used for program input, the preparation signal of the peripheral device is turned off.

087 Using a tape reader/When the perforating machine interface is used for program input, although the read stop is specified, it has been read10After one character, the input cannot be stopped.

090 Due to being too close to the reference point or too slow, the operation of restoring the reference point cannot be performed normally.

091 When the automatic operation is paused (with remaining movement or when performing auxiliary functions), a manual return to the reference point is performed.

092 G27In the instruction, it was found that the instruction position was not the reference point.

100 PWE＝1After the parameter modification is completed, it will promptPWESet to zero and pressRESETThe key.

101 During the process of editing or inputting programs,NCThe power is turned off when refreshing the memory contents. When the alarm occurs, thePWEplace1Turn off the power and hold it down when turning it back onDELETEPress the key to clear the contents of the memory.

131 PMCAlarm information exceeds5Article.

179 597The number of controllable axes set for parameter number exceeds the maximum value.

224 Attempt to execute programmable axis motion instructions before returning to the reference point for the first time.

warranty

New products are guaranteed for one year;For all products and projects that we repair or sell (old parts), we offer a three-month full warranty (i.e. we provide warranty for any type of malfunction during the warranty period). In case of special circumstances, we will communicate with you clearly before the repair. Let you understand and consume with peace of mind.

support

When both of us have already understood each other and you have a certain amount of transactions every month, during the maintenance period of your repair products, as long as we have the same model of finished products in stock, we can lend them to you for free until your repair products are repaired; Whether you have worked with us or not, if you have any technical issues, you can consult us for free by phone, and we will do our best to assist you in solving the problem.

contact information

Dongguan Kesichuang CNC Technology Co., Ltd

Phone:/

Fax:

contacts:a weaponMr./

contacts:kingMiss/

Office Address: Guoxin Commercial Building, Yunhe East Third Road, Nancheng, Dongguan City702chamber