Double jaw tread automatic vulcanizing machine

NegotiableUpdate on 01/12

Model

Nature of the Manufacturer: Producers

Product Category

Place of Origin

Online Consult

Overview

The double jaw vacuum automatic vulcanizing machine is suitable for the production of waterstops, and can also be made into multiple layers to become a tire tread pre vulcanization forming machine, used for pre vulcanization forming of refurbished tire treads

Product Details

　　Double jaw tread automatic vulcanizing machineFeatures:

1. Suitable for vulcanization of various rubber products, it is a hot pressing equipment for pressing and molding various thermosetting plastics. The vulcanizing machine has two heating types: steam and electricity. It mainly consists of three parts: the main engine, hydraulic system, and electronic control system. The oil tank is installed separately on the left side of the main engine and is not affected by the temperature of the heating plate; The control valve is installed on the left side of the host, making it easy for workers to operate and visually spacious.

2. This machine is equipped with a dual pump, which is directly driven by an electric motor. The electric motor is started by a magnetic starter and is equipped with a thermal relay for overload protection. When the electric motor is overloaded or encounters a fault, it will automatically stop.

3. The middle hot plate of this machine is accurately installed in the middle of the four columns and equipped with a guide frame. This machine uses tubular electric heating elements for heating, without the need for a boiler, reducing air pollution, keeping the workshop clean, easy to operate, safe and reliable. Can be used independently, convenient for users. This machine is equipped with an oil storage tank in the lower left corner, which contains oil and is used for circulating the oil pump to do work.

4. This vulcanizing machine is a flat vulcanizing machine used to press various rubber products such as rubber molds, thermosetting plastic products, corresponding specifications of seals, engineering rubber, rubber sheets, etc.

5. This series of products has a high unit area pressure, ensuring the quality of the produced products. According to the process requirements of the products, a push-pull mold device can be configured to reduce labor intensity and costs. Multiple methods such as manual control, electric control, or computer PLC control can be achieved according to customer needs.

　　Double jaw tread automatic vulcanizing machinecommon problem:

serial number	The plunger does not rise after startup	① The oil pump is not producing oil, which may be due to the pump turning in the opposite direction or being damaged. ② The return valve handle is in the open mold position. ③Motor reversal	① Electrical test or disassembly for oil pump maintenance ② Pull the handle to the correct position ③Swap the live wires
2	Abnormal noise	① There is a large amount of air in the pipeline ② Oil filter blockage ③ The oil level in the fuel tank is too low, and air is sucked into the pipeline ④ Oil pump damaged	① Make the press up and down several times, exhaust the air ② remove and clean ③ add oil ④ remove and repair or replace
3	Will not boost or boost slowly	① High pressure pump malfunction ② High pressure relief valve not closed ③ There is a leak on the pipeline ④ Pressure gauge malfunction	① Disassemble, inspect and repair ② After disassembly and cleaning, adjust the pressure correctly. ③ Identify and remove any leaks ④ Replace the pressure gauge
4	Cannot maintain pressure	① The valve seat and disc of the oil discharge valve are not tightly sealed ② The sealing of the valve core inside the one-way valve is not functioning properly ③ Pipeline or oil cylinder leakage reduction	① ② Disassemble, clean, grind or modify ③ Check if the oil inlet pipe is loose, and then tighten it
5	Heating up slower than normal 1) The contactor often opens during the heating process. 2) A certain flat plate is not heating up or the temperature is low. 3) Continue heating up after reaching the specified value	① Temperature controller malfunction ② The temperature control regulator malfunctions or some heating tubes are damaged ③ Temperature controller malfunction ①②③③③⑤⑥	① Replace the temperature controller ② Replace the temperature controller or heating tube ③ Replace the temperature controller
6	There is a large amount of oil leakage around the plunger	The sealing ring is broken	Replace the sealing ring
7	Abnormal heating of the tablet	Damaged thermistor	Measure the continuity of flat electric heating tubes with lower temperatures one by one, and replace damaged meters
8	Temperature control malfunction	① Temperature controller malfunction or control circuit interruption ② Electric heating fuse circuit breaker or wiring circuit breaker	The temperature control instrument core can be removed and compared using the exchange method to replace the damaged meter
9	Heating does not display	①Possible reason is that the ammeter is broken ②Perhaps the heating tube is damaged	Observe the pointer of the temperature controller. If the pointer rotates clockwise to the end, it indicates that the wiring of the thermistor is open or the thermistor is burnt out.
10	The tablet does not heat up	① Thermal resistancedamaged ② Thermal resistanceThe connecting wires at both ends may burn out	① Use the exchange method to check or observe whether the electric contactor is working when the temperature controller is in operation, then connect and disconnect it, and replace the temperature controller. ② Swap the fast melting core or connect the circuit