VH series V-type mixer company

　　Equipment Introduction

This machine can mix dry powder and granular materials of food.

The mixing cylinder structure of this machine ensures uniform mixing, high efficiency, and no material accumulation. The overall structure is simple and easy to operate. The outer surface and material contact parts are made of stainless steel, which has a beautiful appearance and is easy to maintain and clean.

　　Requirement principle structure

One end of the machine is equipped with a motor and a reducer. The motor power is transmitted to the reducer through a belt, and the reducer is then transmitted to the V-shaped bucket through a coupling. Continuously operate the V-shaped bucket, driving the materials inside the bucket to mix up, down, left, and right inside the bucket

　　Principle and Structure

The V-type mixer series products are high-efficiency asymmetric mixers, which are suitable for mixing powder or granular materials in industries such as chemical, food, pharmaceutical, feed, ceramics, metallurgy, etc. The machine has a reasonable and simple structure, operates in a closed manner, and is easy to feed in and out. The cylinder body is made of stainless steel material (manually or vacuum fed), which is easy to clean and is one of the basic equipment of the enterprise.

　　Machine Principles and Structure

One end of the machine is equipped with a motor and a reducer. The motor power is transmitted to the reducer through a belt, and the reducer is then transmitted to the V-shaped bucket through a coupling. Continuously operate the V-shaped bucket, driving the materials inside the bucket to mix up, down, left, and right inside the bucket.

　　purpose

Suitable for mixing powders with good flowability and small differences in physical properties, as well as materials with low mixing requirements and short mixing time. Due to the smooth flow of materials in the V-shaped mixing container, it will not damage the original shape of the materials. Therefore, the V-shaped mixer is also suitable for mixing granular materials that are easy to break and wear, or for mixing finer powders, blocks, and materials containing a certain amount of moisture. It is widely used in industries such as pharmaceuticals, chemicals, and food.

　　Precautions

1. Before use, an air run test should be conducted. Before the test, the firmness of all horizontal connecting parts, the amount of lubricating oil in the reducer, and the integrity of the electrical equipment should be checked. Then, the main switch should be closed, the power should be turned on, and the air run test should be carried out.

2. Installation: Place the machinery steadily, install the machine feet, level them, and ensure that the machinery can operate smoothly.

3. Before use, add oil to the area that needs to be refueled, and then perform no-load operation to check whether the fasteners are loose, whether the electrical system is normal, and whether the mechanical system is running normally. If there are any abnormalities, repair and debug them.

4. Turn the feeding port to the top, open the feeding cover for feeding, and the feeding amount should not exceed the specified volume. Then close the feeding cover tightly and start the machine for operation. If any abnormalities are found during the process, the machine must be stopped for inspection.

5. After work or when changing varieties, the inside and outside of the hopper must be washed clean.

　　Usage and Maintenance

When running with materials, first open the feeding port of the mixer and confirm whether the discharge port is closed. Then, according to the process control requirements, inject the specified amount of materials into the V-shaped hopper. After feeding, in order to prevent material from flowing out during mixing, the feeding port should be closed and locked. Next is the working time of the machine. Turn on the power button, rotate the stop button to the left, start the reverse button of the mixer, adjust the motor speed within the process specified speed, and mix the product at 600r/min. After the mixing reaches the specified time in the process, stop the machine by adjusting the motor speed button. When stopping, make sure that the discharge port of the mixer is facing the ground, and adjust the motor speed button to the 0 position. Rotate the stop button to the right to cut off the power. Then comes the material discharge: open the feeding port of the mixer, use the designated container to load the material at the discharge port until the material in the hopper is completely discharged.

There are still many things we need to pay attention to during the installation and use of this machine, which is beneficial for us to maintain it and increase its service life.

1. Installation: Place the machinery steadily, install the machine feet, level them, and ensure that the machinery can operate smoothly.

2. Before use, add oil to the area that needs to be refueled, and then perform no-load operation to check whether the fasteners are loose, whether the electrical system is normal, and whether the mechanical system is running normally. If there are any abnormalities, repair and debug them.

3. Turn the feeding port to the top, open the feeding cover for feeding, and the feeding amount should not exceed the specified volume. Then close the feeding cover tightly and start the machine for operation. If any abnormalities are found during the process, the machine must be stopped for inspection.

4. When changing varieties, the inside and outside of the hopper must be washed clean. It is suitable for mixing powdered or granular materials in industries such as chemical, food, pharmaceutical, feed, ceramics, metallurgy, etc. The machine has a reasonable and simple structure, operates in a closed manner, and is easy to feed in and out. The cylinder body is made of stainless steel material (manually or vacuum fed), which is easy to clean and is one of the common basic equipment in enterprises.