Technical Specifications for Domestic High Temperature and High Pressure Steaming and Cooking Equipment

Aslitemperature sensorPCT high temperature and high pressure cookerTechnical expertise, with automatic water addition function and automatic water addition when the water level is too low during the test process200h. During the experiment, the circular lining design can avoid the loss of the test sample due to steam overheating impact. The circular door design can seal the temperature and pressure safety lock control, and only when the lock is firm can the testing machine be started. When the pressure inside the box exceeds the limit, it has automatic or manual pressure relief. Timing installation, LED digital timer. When the temperature inside the pot reaches, the timer ensures that the test is completed, and the timing is driven from Table 1.

PCT high temperature and high pressure cookerSpecification testing:

Specifications：PCT-250、PCT-350、PCT-450、PCT-650

Inner box dimensions(W‧H‧D)cm)：￠250 × 300, ￠ 350 × 400, ￠ 450 × 500, ￠ 650 × 600

Inner box material：stainless steel#316

Outer box material：Spray painted or stainless steel plate

temperature range：+100℃~132 ℃ (optional up to 147 ℃ for special customization)

Hydration method：Stainless steel float ball water replenishment

humidification system：electric heating tube

power configuration：Multi resistance solenoid valve with one input and one output power supply

pressurization time：pressure2、0kg/cm2 approximately 45 minutes 3、0kg/cm2 for approximately 55 minutes

voltage(V)：220V~240V50/60HZ single-phase

PCT high temperature and high pressure cookerCharacteristics:

1、Technical expertise, with automatic water addition function and automatic water addition when the water level is too low during the test process200h。

2、The design of the circular lining during the experiment can avoid the loss of the test sample due to steam overheating impact.

3、The circular door design can seal the temperature and pressure safety lock control, and only when the lock is firm can the testing machine be started. When the pressure inside the box exceeds the limit, it has automatic or manual pressure relief.

4、Timed installation,LED digital timer, when the temperature inside the pot reaches, the timer ensures the completion of the test and is driven from Table 1.

5、Accurate pressure, temperature gauge displays the pressure and temperature inside the pot at any time, accurate pressure+0、2~2The0kg/cm2、

6、Before the experiment begins, use a vacuum pump to evacuate and filter the original air of the machine until it is completely fresh air before starting the test.

7、The box has been polished to be durable, aesthetically pleasing, and stain free.

8、During operation, the flowing water automatically discharges unsaturated steam and has reached saturation.

9、Abnormal cause and fault indicator light display, set automatic protectionLimit security.

PCT high temperature and high pressure cookerSafety device:

The environmental temperature of the installation site should not change rapidly, generally at room temperature（25~30)℃，

It should be installed on a horizontal surface (a horizontal box should be used to confirm the level on the ground during installation).

Should be installed in a well ventilated areaExtend the lifespan of the testing machine.

Places where combustibles, explosives, and high-temperature heat sources cannot be tested.

Install as close to the power supply as possible.

PCT high temperature and high pressure cookerStress testing:

Relative pressure:0~4kg/cm2

Pressure inside the pot:0~2The5kg/cm2

Regarding pressure:1The0kg/cm2~2The5kg/cm

A standard atmospheric pressure:101325pa (Pa)=101、3 (kilopascals)

Circulation method: Natural convection circulation of water vapor.

temperature sensorPCT high temperature and high pressure cookerDetailed introduction：

PCT high temperature and high pressure cookerSuitable for national defense, aerospace, automotive components, electronic parts, plastics, magnet industries, pharmaceutical circuit boards, multi-layer circuit boardsIC、LCD、 The testing of sealing performance for products such as magnets, lighting fixtures, and lighting products, as well as accelerated life testing for related products, is used in the design phase to quickly expose product defects and weak links. Test the durability and airtightness of its products.