Price of high temperature, high humidity and high pressure test chamber

1High temperature, high humidity, and high pressure test chamberpurpose

　　High temperature, high humidity, and high pressure test chamberSuitable for national defense, aerospace, automotive components, electronic parts, plastics, magnet industries, pharmaceutical circuit boards, multi-layer circuit boards IC、LCD、 Testing the sealing performance of magnets, lighting fixtures, lighting products, and other related products, conducting accelerated life tests, high-voltage life aging chambers, and three comprehensive testing machines. (Obtaining products, professional technical production, and sales).

IIHigh temperature, high humidity, and high pressure test chamberfeature

　　1.High temperature, high humidity, and high pressure test chamberThe outer box is made of 304 stainless steel plate or stainless steel plate baked paint, and the stainless steel circular test inner box design complies with industrial safety container standards and can prevent condensation and dripping during testing.

　　2.High temperature, high humidity, and high pressure test chamberCircular lining, stainless steel circular lining design, can avoid direct impact of steam latent heat on the test sample.

　　3.High temperature, high humidity, and high pressure test chamberPrecise design, good air tightness, low water consumption, and can last for 200 hours with each addition of water.

4. Automatic access control, circular door automatic temperature and pressure detection, safety access control and locking, safety door handle design. When the pressure inside the box is greater than atmospheric pressure, the testers will be protected by back pressure.

Type 5 packing, when the pressure inside the box increases, there will be back pressure on the packing, which will make it more tightly integrated with the box. Unlike traditional extrusion type *, it can extend the life of the packing.

6. The vacuum action before the experiment can extract the air from the original box and suck in new air (partial<1micorn) filtered by the filter core. To ensure the purity inside the box. <>

7. The critical point limit method automatically provides safety protection, and the abnormal cause and fault indicator light are displayed.

IIIHigh temperature, high humidity, and high pressure test chambertechnical performance

1. Temperature range:+110 ℃ to+132 ℃. (Can produce temperatures up to 151 ℃) 2. Temperature fluctuation: ± 0.5 ℃.

3. Temperature uniformity: ± 1.5 ℃.

4. Humidity range: R.H saturated vapor.

5. Humidity fluctuation: ± 1.5% R.H.

6. Humidity uniformity: ± 3.0% R.H.

7. Pressure range:

(1) Relative pressure range:+0-2kg/cm2. (Note: The production pressure range is+0-4kg/cm2).

　　(2)Pressure: 1.0kg/cm2 to 3.0kg/cm2.

　　(3)Safe pressure capacity: 4kg/cm2=1 atmosphere+3kg/cm2.

8. Circulation method: Natural convection circulation of water vapor.

9. Test time setting: 0-999 hours.

10. Pressure application time: 0.00kg/cm2 to 2.00kg/cm2 for approximately 30 minutes.

12. Heating time: rise from room temperature to+132 ℃ for about 30 minutes, non-linear no-load.

13. The rate of temperature change is the average rate of change in air temperature, not the rate of change in product temperature.

14. The volume of the test inner box is available for selection:

Model number

PCT-25

PCT-35

PCT-45

PCT-65

Internal dimensions

(diameter x D) mm

Φ300*250

Φ450*300

Φ500*450

Φ650*600

Outer box size

（W×H×D）mm

500*500*700

580*850*650

800*750*900

950*900*1100

Loop mode

Natural convection cycle of water vapor

Security protection

Water shortage protection, overpressure protection (with automatic/manual water replenishment function, automatic pressure relief function) accessories

Stainless steel partition with two layers

Power supply

AC220V or AC380V, 50/60Hz.

Note:

1. The performance measured after stabilizing for 30 minutes without test load or scaffolding.

2. The temperature rise and fall time refers to the performance measured by an air-cooled system when the ambient temperature is 26 ℃± 5 ℃.

3. The temperature and humidity sensor is installed at the air outlet of the air conditioning unit.

4. Temperature and humidity uniformity is defined as the measured data of temperature and humidity at the geometric center point of the laboratory.

5. The performance, measurement, and calculation methods of the above data shall be determined according to the methods specified in GB5170.2 and GB5170.5.

4High temperature, high humidity, and high pressure test chamberExecution and compliance with standards

1. GB/T10586-1989 Technical conditions for wet heat testing laboratory;

GB2423.3-93 (IEC68-2-3) Constant Damp Heat Test; 3. MIL-STD810D method 502.2;

4. GJB150.9-8 Temperature and Humidity Test;

GB2423.34-86, MIL-STD883C Method 1004.2 Temperature humidity, high voltage combined cycle test;