Wholesale of fully automatic circulating water multi-purpose vacuum pump

Circulating water multi-purpose vacuum pump SHB-B95The series is a vacuum pump that uses circulating water as the working fluid and generates negative pressure through fluid jetting. Providing vacuum conditions for processes such as evaporation, distillation, crystallization, drying, sublimation, filtration and depressurization, and degassing, it is particularly suitable for laboratories and small-scale experiments in industries such as colleges and universities, research institutes, chemical engineering, pharmaceuticals, biochemistry, food, pesticides, agricultural engineering, and biotechnology.

● Recycling water to save valuable water resources.

Compared to other types of vacuum pumps, it saves more than 35% electricity.

Specially designed fluid muffler reduces gas in water, making the vacuum degree higher and more stable; Reduce gas-liquid friction and lower noise.

Five tap, single meter display, can be used separately or in parallel.

Acid, alkali, and solvent corrosion resistance.

The motor is manufactured by the motor manufacturer ODM and sealed with fluororubber. There is no corrosive gas entering the interior of the motor.

▲ It is necessary to regularly replace the water in the sink to ensure pure water quality, maintain vacuum degree, and avoid scale stains.

▲ Can be used to extract corrosive gases, but the water change cycle needs to be shortened.

（1）SHB-B95Type circulating water multi-purpose vacuum pump,The shell adopts cold plate spray coating，Pump head host.for304 stainless steel, jet injectorThe check valve is made of copper and has a suction nozzle The three-way valve is made of PP material, with good corrosion resistance, heat resistance, low temperature strength, and mechanical properties. The vacuum pipeline is made of rubber pipe.

（2）ZKB-B95Type circulating water multi-purpose vacuum pump,The shell is made of 201 stainless steel，Pump head host.injectorfor304 stainless steelThe check valve is made of copper and has a suction nozzle The three-way valve is made of PP material, with good corrosion resistance, heat resistance, low temperature strength, and mechanical properties. The vacuum pipeline is made of silicone tubing.

(3) ZKB-B55A circulating water multi-purpose vacuum pump,The housing is made of304 stainless steel，Pump head host.injectorCheck valve and exhaust nozzlefor304 stainless steelThe three-way valve is made of PP material, with good corrosion resistance, heat resistance, low temperature strength, and mechanical properties. The vacuum tube pipeline is made of silicone tubing.

（4）ZKB-B95TType circulating water multi-purpose vacuum pump,shellPump head hostadopt304 stainless steel, PP material for tee, jet injector The exhaust nozzle is coated with PTFE and equipped with a check valve The exhaust nozzle is made of PTFE material, and the vacuum pipeline is made of PTFE tubing.

Circulating water multi-purpose vacuum pump SHB-B95parameter table

Usage:

1. When in use, open the top cover of the water tank and inject clean cold water (water can also be added through a drain hose). Stop adding water when the water level indicator reaches the highest level (not exceeding the maximum water level). Frequent use: Change the water at least twice a week. If the water pollution is severe and the usage rate is high, the time for changing the water should be shortened to keep the water in the tank clean.

2. Vacuum pumping operation. Tightly connect the suction sleeve of the equipment that needs to be vacuumed to the suction nozzle of this machine, turn off the circulation switch, turn on the power, and turn on the power switch to start the vacuuming operation. The vacuum degree can be observed through the vacuum gauge corresponding to the suction nozzle. Five exhaust nozzles can also be used in parallel.

3. When the machine needs to operate continuously for a long time, the water temperature in the water tank will rise, affecting the vacuum degree. At this time, the drain hose can be connected to the water source (tap water), and the overflow nozzle can be used as the drainage outlet. By controlling the flow rate of tap water appropriately, the water temperature in the water tank can be kept from rising, and the vacuum degree can be stabilized.

4. When it is necessary to provide cooling circulating water for the reaction device, based on the third operation above, connect the inlet and outlet pipes of the device that needs to be cooled to the circulating water outlet and inlet nozzles on the side of the machine, and turn the circulating water switch to the ON position to achieve circulating cooling water supply.

Warranty and Service:

Within one year of sale, if the product malfunctions due to user use according to regulations, our company is responsible for repairing it. If the malfunction occurs beyond the warranty period, our company can also repair it and charge for component costs and repair fees.

Before using this product, please read the product manual carefully and operate it strictly according to the regulations. If there are any quality problems, please contact our company in a timely manner. We provide consultation and repair services at any time to meet the requirements of users