Stainless steel electric heating mixing tank

The stainless steel mixing tank produced by Hubei Chuangte Machinery has an inner and outer layer, a vertical mixer, and an open cylindrical stainless steel container body. It can withstand acid and pressure, maintain insulation and cooling, and has the advantages of beauty and practicality. It is suitable for industries such as food, pharmaceuticals, cold drinks, dairy processing, animal husbandry, and chemical industry. It is an essential equipment for heating, cooling, insulation or storing slurry, especially for milk pasteurization and insulation. It has the advantages of heat exchange effect and reasonable structure.

Stainless steel mixing tankThe tank body, tank cover, stirring blade, feed inlet, and discharge valve are all made of imported stainless steel acid resistant copper 1cr18Ni9Ti, according to the technical conditions of GB741-80. The inside and outside of the tank body are polished, and there is a stirring blade inside the tank, which plays a stirring role during operation; There is a thermometer on the top cover, which displays the temperature inside the tank; There is a cycloidal pin planetary reducer at the top, which drives the mixing blade; It can be disassembled and cleaned, and has an openable tank cover for cleaning. In addition, it has two feeding ports that can be connected to pipelines for easy connection of various ingredients. There is a discharge port below, and a plug valve is installed. After mixing evenly, the plug valve handle can be rotated 90 ° to discharge the material. After discharging, it is closed to achieve uniform mixing.

Technical parameters of stainless steel mixing tank

1、 容积： 50L、100L、200L、300L、500L、600L、1000L～6000L。

2. Heating method: Using an electric heating rod inserted into the jacket, heating evenly without any cold zone. Inject thermal oil or water into the jacket as a heating medium to generate heat energy and heat the materials inside the tank.

3. Material heating temperature: ≤ 350 ℃; Material heating time: 20min to 90min (depending on process requirements).

4. Temperature control: Temperature is measured using an electric thermocouple and connected to a temperature controller for temperature control (temperature difference ± ≤ 1 ° C), and the temperature of the material can be adjusted. The temperature controller is installed inside the electric control box, and the temperature transmission rod is inserted directly into the bottom of the tank, so that the temperature of the liquid can be indicated even when it is in a low position.

5. Ingredient tank body: The inner surface is mirror polished with a roughness Ra ≤ 0.4 μ m.

6. Upper cover: It is a two leaf movable cover that is easy to clean, with mirror polished inner and outer surfaces (roughness Ra ≤ 0.4 μ m).

7. Inner tank bottom structure: It is processed into an R angle by spinning, welded and polished to the inner tank body, and tilted at a 5 ° angle towards the discharge port for easy discharge of materials without any retention.

8. Jacket form: Full jacket, used to add thermal oil or water to achieve suitable heating and cooling during operation.

9. Thermal insulation material: filled with pearl cotton, rock wool or polyurethane casting foam to maintain a temperature difference with the outside and achieve thermal insulation effect.

10. Surface treatment method for the outer shell: mirror polishing or 2B primary matte or 2B frosted matte treatment.

11. Mixing device: The top center is used for mixing, and the output shaft of the reducer is connected to the mixing blade shaft with a flexible sleeve for easy disassembly and cleaning.

12. Mixing speed: 15-120r/min (constant speed); Mixing blade forms: frame type, anchor type, blade type, turbine type, etc. (according to process requirements).

13. Ingredient tank configuration: electrical control box, temperature meter, liquid inlet and outlet, medium inlet and outlet (oil inlet and outlet), drain port (oil overflow hole), etc.

14. Material of ingredient tank: SUS304 or SUS316L for the inner tank body; The jacket is made of Q235-B or SUS304; The outer protective shell is made of SUS304.

15. The process openings of each inlet and outlet pipe and the welding points of the inner tank body adopt the flanging process arc transition, which is smooth, easy to clean, and has a beautiful appearance.